- 相關推薦
解析驗證EIGRP STUB區域
IGRP STUB區域設置了之后，路由器在丟失路由條目的時候不會向 STUB區域發查詢消息，在上述top中我們可以把Rc做成 STUB區域，假如Rb的loop0 口down掉了之后，Rb不會向Rc發送查詢消息。下面是小編帶來的實例，歡迎學習!
我們先在這3太路由器上全部啟用EIGRP 10 ，所有的接口都參與到EIGRP 10 在沒有設置stub的時候，得到路由表如下：
RA：
1.0.0.0/24 is subnetted, 1 subnets
C 1.1.1.0 is directly connected, Loopback0
2.0.0.0/24 is subnetted, 1 subnets
D 2.2.2.0 [90/2297000] via 12.1.1.2, 00:01:26, Serial2/1
3.0.0.0/24 is subnetted, 1 subnets
D 3.3.3.0 [90/2297000] via 12.1.1.2, 00:00:37, Serial2/1
23.0.0.0/30 is subnetted, 1 subnets
D 23.1.1.0 [90/2297000] via 12.1.1.2, 00:01:26, Serial2/1
12.0.0.0/30 is subnetted, 1 subnets
C 12.1.1.0 is directly connected, Serial2/1
Rb：
1.0.0.0/24 is subnetted, 1 subnets
D 1.1.1.0 [90/2297000] via 12.1.1.1, 00:02:30, Serial2/1
2.0.0.0/24 is subnetted, 1 subnets
C 2.2.2.0 is directly connected, Loopback0
3.0.0.0/24 is subnetted, 1 subnets
D 3.3.3.0 [90/2297000] via 23.1.1.1, 00:01:41, Serial2/2
23.0.0.0/30 is subnetted, 1 subnets
C 23.1.1.0 is directly connected, Serial2/2
12.0.0.0/30 is subnetted, 1 subnets
C 12.1.1.0 is directly connected, Serial2/1
Rc:
1.0.0.0/24 is subnetted, 1 subnets
D 1.1.1.0 [90/2297000] via 23.1.1.2, 00:02:06, Serial2/2
2.0.0.0/24 is subnetted, 1 subnets
D 2.2.2.0 [90/2297000] via 23.1.1.2, 00:02:06, Serial2/2
3.0.0.0/24 is subnetted, 1 subnets
C 3.3.3.0 is directly connected, Loopback0
23.0.0.0/30 is subnetted, 1 subnets
C 23.1.1.0 is directly connected, Serial2/2
12.0.0.0/30 is subnetted, 1 subnets
D 12.1.1.0 [90/2297000] via 23.1.1.2, 00:02:06, Serial2/2
下面，我們開始試驗，在Rc上沒有設置stub的時候，在Rb上打開debug
RB#debug eigrp packets query
RB EIGRP Packets debugging is on
(QUERY)
RB#config t
Enter configuration commands, one per line. End with CNTL/Z.
RB(config)#
RB(config)#int loopback 0
RB(config-if)#shu
*Mar 1 00:16:38.587: EIGRP: Enqueueing QUERY on Serial2/1 iidbQ un/rely 0/1 serno 6-6
*Mar 1 00:16:38.591: EIGRP: Enqueueing QUERY on Serial2/1 nbr 12.1.1.1 iidbQ un/rely 0/0 peerQ un/rely 0/0 serno 6-6
*Mar 1 00:16:38.599: EIGRP: Sending QUERY on Serial2/1 nbr 12.1.1.1 (向RA發送查詢)
*Mar 1 00:16:38.603: AS 10, Flags 0x0, Seq 10/3 idbQ 0/0 iidbQ un/rely 0/0 peerQ un/rely 0/1 serno 6-6
*Mar 1 00:16:38.607: EIGRP: Enqueueing QUERY on Serial2/2 iidbQ un/rely 0/1 serno 6-6
*Mar 1 00:16:38.611: EIGRP: Enqueueing QUERY on Serial2/2 nbr 23.1.1.1 iidbQ un/rely 0/0 peerQ un/rely 0/0 serno 6-6
*Mar 1 00:16:38.619: EIGRP: Sending QUERY on Serial2/2 nbr 23.1.1.1 (向RC發送查查詢)
*Mar 1 00:16:38.623: AS 10, Flags 0x0, Seq 11/3 idbQ 0/0 iidbQ un/rely 0/0 peerQ un/rely 0/1 serno 6-6
可以看到，沒有設置stub的時候 Rb會向RA和 Rc發送查詢消息。下面我們把Rc做成 STUB區域.
我們先把RB上的loopback 0 打開，讓網絡回到正常的收斂
Rb(config-it)# int lo 0
Rb(config-it)#no sh
然后把RC設置成STUB區域
RC(config)#router ei 100
RC(config-router)#eigrp stub receive-only
再關掉RB上的loopback 0
再來看RB的查詢情況：
*Mar 1 00:28:13.139: EIGRP: Enqueueing QUERY on Serial2/2 iidbQ un/rely 0/1 serno 9-9
*Mar 1 00: 28:13.143: EIGRP: Enqueueing QUERY on Serial2/2 nbr 23.1.1.1 iidbQ un/rely 0/0 peerQ un/rely 0/0 serno 9-9
*Mar 1 00: 28:13.151: EIGRP: Enqueueing QUERY on Serial2/1 iidbQ un/rely 0/1 serno 9-9
*Mar 1 00: 28:13.155: EIGRP: Enqueueing QUERY on Serial2/1 nbr 12.1.1.1 iidbQ un/rely 0/0 peerQ un/rely 0/0 serno 9-9
*Mar 1 00: 28:13.163: EIGRP: Sending QUERY on Serial2/1 nbr 12.1.1.1 (向RA發送查詢)
*Mar 1 00: 28:13.163: AS 10, Flags 0x0, Seq 19/8 idbQ 0/0 iidbQ un/rely 0/0 peerQ un/rely 0/1 serno 9-9
*Mar 1 00: 28:13.351: EIGRP: Received QUERY on Serial2/2 nbr 23.1.1.1
RB(config-if)#
*Mar 1 00: 28:13.355: AS 10, Flags 0x0, Seq 11/21 idbQ 0/0 iidbQ un/rely 0/0 peerQ un/rely 0/0
自始至終沒有發現去往Rc的查詢消息，所以，EIGRP的 STUB區域驗證成功。
【解析驗證EIGRP STUB區域】相關文章：
華為認證考試輔導：stub、nssa區域配置10-13
EIGRP帶寬實例配置09-19
EIGRP協議理論詳解06-28
XMLSchema驗證11-05
oracle口令文件驗證與操作系統驗證設置技巧10-30
ASP加法驗證碼代碼07-01
法語語法解析之指示代詞用法解析07-11